Roborock S6 MaxV Teardown of Smart Robot Vacuum. Used KIMO T20 Cordless Drill Driver Kit for TOOLS!!
HTML-код
- Опубликовано: 6 фев 2025
- The Roborock S6 MaxV is considered the smartest Robot Vacuum to date with its industry leading navigation and upgraded dual camera system.
In this video we will be taking apart the Roborock S6 MaxV and go over the components that make up this great robot vacuum. Can I Tear down this robot and be able to put it back together??? I think I am missing a few screws!!!
Need a Versatile Electric Drill, check out the one I personally used for this tear down video!!!
amzn.to/35XXIcT
Business Inquiries: nate2003@comcast.net
Robot Masters Website: www.robottechreviews com
Participant in affiliate marketing any clicks and use of my links I do earn a small commission off the links. Thank You sooo much for your support!!! 
Наука
Is this the only channel that does vacuum robot video breakdowns in the history of RUclips? Bravo, Robot Master. 👏
Hahaha there a few others out there 😅
3 years old but still useful! Thank you for the video and the proper explanation. On my version there was a rubber gromit that went over the camera and required a bit of finesse and tweezers to get it back on
How did you do that? I need to know how I have the same problem 😢
Same problem for me!
Если есть инструмент для доставания всяких уплотнений в виде загнутых острых крючков, ставится обратно за 2 минуты. На алиэкспресс стоит очень дешево, но неимоверно полезен.
Thank you! I slowed down the video at 9:35 to 0.25x speed because you removed those base plate screws so fast! I took the unit apart to solve the error "filter wet or clogged" when it is actually just a build up of lint and dust in every nook and cranny plus in the intake screen of the fan motor.
Favourit robot vacum youtuber. You should do other stuff as well!
😊
how have you put back front bumper?
there is a rubber cover is hard to put back
Yeah take some needle nose pliers or a small screwdriver. Carefully align the rubber gasket around the camera system. There a small grove that the gaskets sits on to prevent dust to enter the camera housing.
@@RobotMasters Thank you 🙏
I removed it easily, and then realised that it not so easy to put it back 😂
This was super helpful! Had to replace one of the driving wheels myself, but noticed you hadn't been able to remove the wheels. The axle is accessible if you pop the cliff/IR-sensors just up (push it with a snap from the camera towards the wires) and then you can slide it out with a thin rod!
Thanks for the tips, I thought you needed a special punch out tool 🙂
I'm not sure I understand how to remove the cliff sensor. . . I tried to pry it upwards, but it has fingers holding it in place. . . I was afraid of breaking the damn thing. . . "Push it with a snap from the camera towards the wires" What camera? What wires? Far as I know there are no cameras on this bot. . . Just lasers and ir sensors. Wish someone would show such things on a video. . . Every video does these things on an S5, and the S6 design makes it a bear to change wheels . . .
@@thenewmusicsculptors3650 bruh, there is literally TWO cameras on it, and they are right in front. A normal and an IR cameras
@@Alfamaxis Yeah. . . I figured it out, after some turbulence, but my model actually is not the Max model. . . just an s6. I think that it (plainjane s6) doesn't have a regular camera. . . and I'm not sure you'd classify most IR sensors as cameras. . . more like a distance sensing gadget for near objects. I'm pretty sure, after consideration, he was referring to the business end of the sensor, which faces downward on the bot, and the wire plug in end of the sensor, which is at the top of the bot.) So. . . After the carcass is completely disassembled push the sensor up till it snaps out. . . at least that's my translation.
@@thenewmusicsculptors3650 well, actually s6 maxv can see in the dark thanks for it's IR camera, and it's actually a camera, you can even see through it on the roborock app
13:01 When you disassemble a robot vacuum and your friend asks if you broke it.
Great interesting video! That sucks about the drive wheels. We should be able to replace those.
The original models was a lot easier to replace
Thank you for this i needed to replace the motor wheel its actually very easy all u need to do is slide the sensor up and outta the slot its in and u an just use anything tiny to push the rod out the Motor is connected with an extra 2 little gray wires be careful u will need a tiny but to undo the very small pcb that those wires run to it looks like they come as a unit not the same as the s6 or older models
Thanks for the tip!!!
I just replaced the motor and used this video: ruclips.net/video/Wc-zeVOcWAs/видео.html to get an idea of the grey cables mentioned and how to push the rod down.
It was not initially clear to me that the sensor should be pushed up in order to push the rod out :)
The extract bar are taged by small pins to the the silicon edge in the other side of robot. After unfastening it, remove the 2 joint axles, forcing them slightly so the piece comes out. finally unscrew the brush motor (white piece on one side)
Glad you created this video, I can see myself disassembling my stupid s6 maxv. I have only 3 weeks with the vacuum, and the experience has been horrible. two replacements in this short period of time. First one having problems with the Wifi, second one started with "bumper error" right out of the box.
Sorry to hear, hopefully you got a working model or a different brand.
Thank you for all of your great videos.
I’m getting an error 4 message.
Cliff sensor error. Clean the cliff sensors, move the robot, and restart.
I have tried to do these instructions and it just keeps spinning in a circle.
Any advice ?
“I could replace the motor for 50 cents...but I bought the whole lidar unit for about $100 bucks” 😂 This guy. 😆
Hahahaha, I didn't feel like soldering two connections 😮😮😮😒😒😒 Don't judge ME 😆😆😆😆
Just wanna replace the side wheel, should i do all of them?
Do you have a video for the s6 ? I am having and issue with the left wheel, I want to try and replace it myself
Hi, How to take out those two big wheels ?
8:53 ok how do you install that rubber back on cameras?
It takes some finesse but just push the rubber dust grommet in and wiggle back and forth. It does take awhile to slot in the groove.
@@RobotMasters 4 hours later: so the window can be unattached, then you can fit the rubber back in place, attach the window and screw the arc. But in general if you see a few dust in there, IGNORE.
@@kev4ev Yeah it definitely not easy, pretty sure the factory has a specialized tool.
Observe back area of window. On the bottom it has 2 cylinder shaped notches. Press on them down (outward) and window comes out of the frame.
You put bumper back on, and align gasket easily in a minute because you have full access to camera notch. Then you put window back up and screw all screws in bottom baseplate that connects with bumper. Note that center 2 screws fit in exactly in that 2 cylinder shaped notches that you used before to push window out!
@@abccde3832 You are my hero!
Where’s the exhaust fan/filter?? I’ve been reading that decreases performance could indicate a clogged exhaust, but I’m not sure where it is.
The exhaust fan the circular plastic unit with a few wires attached to it.
@@RobotMasters found it! Do you see an easy way to clean any clogging in there without opening it? Push air in from outside??
@Tech do Liberal Unfortunately no, the casing required opening to access the fan unit.
I need to replace the fan, can I only remove top part to get to fan or do you have to also remove bottom?
Not sure are you talking about the fan housing? Anyway the two pieces split apart, held on by a few plastic pressure clips. For those just take a flat head screw driver and gently lift up on the clips. Yes you do have to take the top part of the robot off to access the fan unit.
Hi, I have error 109 what I need to do?
I have made reset and clean everything…
Hello, my unit vacuumed dog poop and a family member decided to run water on to clean it now the unit doesn’t work. Start button just flashes. Any idea what I may need to do to fix it?
My recommendation is let it dry out for 3-5 days. Try to remove the battery while the robot fully dries. Once the 3-5 days are up try recharging the robot and running it.
Interesting design
Yeah I have taken apart several different models of the Roborock and a few from iRobot. I found the Roombas to have the best repairability, all the components are modular. The New S6 MaxV was harder to replace some of the components compared to its previous models.
There a lot of tech in that robot. In 5 years maybe iRobot will be packed with that level of technology. ;D nice video!
Thanks, that will be something to see a Lidar based Roomba!!!
Where can i find the speaker? I would like to disable this.
Look for the exhaust vent on the robot, the opposite side is usually where the speaker located. It looks like an exhaust vent too, but it not. If you are unsure run the vacuum and feel for the air flow. The other side the speaker.
@@RobotMasters Thank you for the message. Do you have any idea if it is just unplugging cable or?
@@jon964 I can't recall, you might need to cut one of the wires
Hi There can you explain how to run this robot without - WiFi - ex. disconnecting some wire from the board etc.?
Hmmmm look for a thin wire that not connected to anything, that usually the WiFi antenna,
@@RobotMasters the wifi module dosen't have external antena it looks like integrated in bda module
@@stanisawbiaas827 OK not sure how to discount the board, if it integrated directly in the circuit board. Is there any ribbon cable you can discount that link to the WiFi module?
hi, I want to ask a question about battery performance and life in general. I am using s5max. When will the battery lifetime start to decrease if we use it at least once a day and everyday in a week ?
It really depends on what lithium battery they are using. You can expect 300 - 1,000 complete charges to discharge cycles before you may notice a decrease in battery life. Usually 2-5 years, remember the robot will auto recharge once the battery gets to a certain charge level and resume where it left off. I don’t think you will notice the decrease in battery performance or be affected by it if it does happen.
@@RobotMasters it is roborock s5max.
@@baranbaris1172 Yes applies to S5 Max
Great video thank you very much. I just need to ask you something. I was using white vinegar and bleach for mopping. Now I think the water way is clogged somewhere. What can I do? any recommendations would be appreciated. Thanks.
Unless you are comfortable opening the robot up and void your warranty I recommend asking Roborock for servicing. If you are willing to take the risk, you may need to open the robot up and try to clear the water hose.
@@RobotMasters Thank you for your prompt resonse. However, I do not think the servis would help me as I used vinegar and bleach for mopping. They would understand easly. I’ll try to clean the pipes. Cheers.
temizleyebildin mi? Ben az deterjan falan koyuyordum tıkandı su çok az geliyor. Nasıl temizlenir bu
Great tear down demonstration! Are most parts readily available?? I see one comment that has had a couple of issues right out of the the box! How does the warranty work & how long is the warranty?
You can find parts through 3rd parties, but they are hard to come buy. I do recommend going through Roborock if you are still under warranty, which is a year I think.
Thumbs up for Sparkles 👍🏻😁
Hahaha Sparkles was a big help!!!
Awesome video from our favourite youtuber,The build quality of s6 max v look pretty solid.Its smarter than deebot t8 plus?
Hahaha the T8 has a little more tech inside. An extra motor to drive the other side brush. Everything else is about the same.
@@RobotMasters the t8 +?the white t8?
@@geokokos3796 Hmm don't know where I can get a white T8 🤔🤔🤔
Thanks a lot. It is very useful !!
In need to order the lift wheel moter
How to remove the main wheels from the s6 MaxV?
how do you remove the wheel?
13:17 Me when I'm on my lunch break.
Super video
🤗🤗🤗🤗
suction turbine seems similar to iRobot Scooba 3xx or Roomba S9
Courageous
I was surprised it still worked afterwards 😬
io ho smontato anche il sensore paraurti e la ruota destra
Nice
Thanks
2:11 Good you didn't throw it in the trash can.
LOL I was close too
Geez I kept hearing the parts hitting the floor during the video.
Puffer fish